completely rebuilt my nighthawk 700 sc but short two tappets, are they "lashes"?

DirtyMrRogers Topic starter

Contributing Member

Offline

Gender: Male

Age: 27
Location: Small town near Austin, Tx
Bike: 1984 Nighthawk Sc 700c.c.
Posts: 213

Join Date: Dec, 2009

completely rebuilt my nighthawk 700 sc but short two tappets, are they "lashes"?

« on: February 10, 2010, 08:51:48 AM »

I am looking up two hydrolic tappets for my 700 to replace two that are less than desired, and at honda in Austin they are $50 a piece, so I figured I'd see if any of ya'll had a pair, or knew where to get them, also... I'm trying to look them up on the microfishe but are they labeled something different? anyway, rebuild went amazing considering... turns out I had a scorched crankshaft because of a blown #2 cylinder bearing, a piston rod, a bent engine mounting rod (holds the cylinders attached to the block) and two blown tappets. everything else went great once we got rebuilding, but I can tell you LOCK-TIGHT EVERYTHING, TORQUE PRECISELY, AN EXTRA SET OF HANDS ARE A MUST, TEST THINGS THAT SEEM LIKE THEIR WORKING, DIESEL AND KEROSENE CLEAN EVERYTHING, RAZOR BLADES REMOVE CARBON BUILD UP, COMPLETE GASKET SETS ARE NOT NEARLY COMPLETE!
Thanks for any advise and ride safe. see you this summer.


	Logged

Ride my nighthawk? I'd rather let you ride my wife.

SmokinFast

Contributing Member

Offline

Location: USA
Posts: 183

Join Date: Oct, 2008

Re: completely rebuilt my nighthawk 700 sc but short two tappets, are they "lashes"?

« Reply #1 on: February 11, 2010, 02:21:47 AM »

I have several extras. I'll trade you for an alternator chain which i need desperately.


	Logged

DirtyMrRogers Topic starter

Contributing Member

Offline

Gender: Male

Age: 27
Location: Small town near Austin, Tx
Bike: 1984 Nighthawk Sc 700c.c.
Posts: 213

Join Date: Dec, 2009

Re: completely rebuilt my nighthawk 700 sc but short two tappets, are they "lashes"?

« Reply #2 on: February 12, 2010, 11:18:34 PM »

Only alternator chain is on bike... I have a Crankshaft that needs to be milled in the second cylinder rod slot/ an old windscreen that is scratched but not totaled/ I'm also removing the mud flap of a liscense plate holder.
Cash?


	Logged

Ride my nighthawk? I'd rather let you ride my wife.

SmokinFast

Contributing Member

Offline

Location: USA
Posts: 183

Join Date: Oct, 2008

Re: completely rebuilt my nighthawk 700 sc but short two tappets, are they "lashes"?

« Reply #3 on: February 13, 2010, 12:55:23 AM »

Quote from: DirtyMrRogers on February 12, 2010, 11:18:34 PM

I located an alternator chain today. I'll send you a PM with details about the tappets.

Brett


	Logged

DirtyMrRogers Topic starter

Contributing Member

Offline

Gender: Male

Age: 27
Location: Small town near Austin, Tx
Bike: 1984 Nighthawk Sc 700c.c.
Posts: 213

Join Date: Dec, 2009

Re: completely rebuilt my nighthawk 700 sc but short two tappets, are they "lashes"?

« Reply #4 on: February 22, 2010, 09:10:32 PM »

brettbolt sent me the tappets, they are in perect working condition. They were recieved earlier today, and installed now... Just looking to see what oil to put in the oil defoaming chambers, right now. hopefully installing the freshly rebuilt bike engine tomorrow after working on the ga tank paint prep tonight.


	Logged

Ride my nighthawk? I'd rather let you ride my wife.

fishmeister

Guest

Re: completely rebuilt my nighthawk 700 sc but short two tappets, are they "lashes"?

« Reply #5 on: February 22, 2010, 09:31:21 PM »

Nothing better for oil.

gn4.jpg (38.51 KB, 410x517 - viewed 222 times.)
	Logged

Pages: [1] Go Up

« previous next »

	Author	Topic: completely rebuilt my nighthawk 700 sc but short two tappets, are they "lashes"? (Read 1388 times)
0 Members and 1 Guest are viewing this topic.